UV Gang Sheet Builder

Auto Nest. Upload your designs, set your sizes, and let the builder pack the sheet for you. Adjust by hand afterward if you want.

Detail that vinyl can't do. Hairline script connections, scattered small elements, gradients, and photographic artwork all print in one pass with no weeding.

Full color on any surface color. Bright ink reads just as sharp on a black tumbler as it does on stainless.

You control the layout. You're the designer, we're the printers.

All sheets are 22 inches wide. No setup fees, no art fees, no minimum order.

• 22" x 4" is $18
• 22" x 12" is $22
• 22" x 24" is $34

You pay for the sheet, not the number of designs on it. Filling a 22" x 24" sheet edge to edge gets you roughly three times the print area of the small sheet for less than twice the price, so packing it tight is where the savings are.

Works on: stainless tumblers and water bottles, ceramic mugs, glass, bare and painted metal, laptops, hard plastic phone cases, acrylic, coolers, and toolboxes.

Won't work on: fabric, silicone, rubber, or textured surfaces. Quick test: if the item flexes when you squeeze it, it's the wrong surface for this product.

Single curves like a tumbler are fine. Keep designs off the tapered section near the base, where the curve tightens and the film will wrinkle.

Not sure about your item? Full surface breakdown here, or bring it by the shop.

1. Clean with isopropyl alcohol and let it dry completely. Skip dish soap and glass cleaner, both leave a residue the adhesive bonds to instead of the surface. Clean new drinkware too, it carries manufacturing oils.

2. Pre-squeegee the sticker. Before separating anything, run a squeegee firmly over the design a few times. Give thin lines and small separated pieces extra passes. This is what gets the whole design to lift cleanly onto the carrier film.

3. Dry fit. Hold it in place and check your position. Once the backing is off, the adhesive grabs on contact and it will not survive being repositioned.

4. Separate the layers slowly, watching to confirm every element lifts onto the clear top film. If a piece stays behind, lay it back down, re-squeegee that spot, and try again from a different angle.

5. Apply from the center out. On a tumbler, press one vertical edge down first, then roll the tumbler slowly while smoothing forward with the card. Rolling is what prevents wrinkles on a wrap.

6. Peel the top film slowly at a low angle, not straight up, then do a final press over the edges and fine detail.

Full application walkthrough and troubleshooting

Wait 48 hours before the first wash. The adhesive keeps bonding after application and reaches full strength over about two days.

Hand wash only. Not dishwasher safe. Dishwasher heat and high pressure jets will lift the print. This is the instruction customers skip most often.

Mild soap and a soft cloth. Skip abrasive scrubbers, bleach, and solvent cleaners, and don't soak the item for long periods.

Standard turnaround is 24 to 48 hours, Monday through Friday. Printing runs 9 AM to 5 PM on business days. Orders placed Friday afternoon through the weekend begin processing the following Monday. We do not print on weekends.

Free local pickup at 3030 Knolin Dr in Bossier City, or shipped anywhere. Free shipping on orders over $100.

Your designs arrive arranged on one sheet and are not pre-cut, so you'll cut them apart with scissors.

Upload PNG files at 300 DPI with a transparent background. Any white left in the file prints as white ink, and on a stainless tumbler there is nowhere for it to hide.

Common sizes: a 30oz tumbler full wrap runs about 10.5 to 11.5 inches wide. Mugs and front-only tumbler designs run 3 to 4 inches. Laptop lids run 8 to 10 inches.

Tumbler dimensions vary by brand at the same stated capacity. Wrap a paper strip around the section you are decorating, mark where it meets, and measure it flat.

We print exactly what you upload and do not alter artwork, so double check sizing and spelling before you order.